新闻动态
NEWS
/
/
/
How should the bending machine be operated? This can improve its work efficiency!

How should the bending machine be operated? This can improve its work efficiency!

  • Time of issue:2020-10-26 17:34
  • Views:

How should the bending machine be operated? This can improve its work efficiency!

(Summary description)I believe that everyone has a certain understanding of the bending machine, but everyone knows its specific functions, but they are still unclear about its correct operation method and operation process. In fact, it......

  • Time of issue:2020-10-26 17:34
  • Views:
Information

  

安徽省亚威机床制造有限公司

 

I believe that everyone has a certain understanding of the bending machine, but everyone knows its specific functions, but they are still unclear about its correct operation method and operation process. In fact, its operation process is mainly divided into pre-operation and operation. The details of the process in several aspects such as after work and after work, and if you want to improve its use efficiency, you also need to use some skills. In the article, the editor will focus on its specific work process and methods to improve its efficiency. Let me give you a detailed introduction.

  

 

The specific operation process of the bending machine:

1. Before work

Before the operation of the bending machine, it is necessary to manually turn the machine through a working process to ensure that the equipment can be opened after it is normal. Then carry out a very detailed inspection of the shearing machine, and then open the air valve to release the air in the system. To turn on the power of the bending machine, turn on the key switch on the control panel, then press the oil pump to start, and after a series of operations, you will hear the sound of the oil pump rotating. The machine does not work at this time.

2. When working

When the bending machine is working, do not stack the sheets, and do not trim the burrs. The bottom plate should be tight and reliable, and the upper and lower blade surfaces should be kept parallel. When the bending machine is used, it cannot be carried out under the condition that the pressure is not tight. The balance and firmness of the blade must be paid attention to in the operation of the bending machine.

3. After work

After the operation of the bending machine is completed, the switch should be turned off, and then checked, whether the valve has been closed should be closed, and the upper blade should be placed on the bottom.

 

Methods to improve the operating efficiency of the bending machine:

1. Before starting the bending machine, carefully check whether the motor, switch, circuit and grounding are normal and firm, and check that the operating parts and buttons of the equipment are stuck in the correct position.

2. Check the coincidence and firmness of the upper and lower dies of the bending machine, and check whether each positioning device meets the requirements to be processed.

3. When the upper slide plate and each positioning axis are not at the origin, run the back-to-origin program.

4. After the bending machine is started, it will run idly for 1-2 minutes, and the upper slide plate will move 2-3 times in full stroke. If any abnormal sound or fault is found, it should be stopped immediately, the fault will be eliminated, and everything will work normally.

5. The bending machine should be under the unified command of one person, so that the operator and the feeding and pressing personnel are closely coordinated to ensure that the cooperating personnel are all in a safe position to send the bending signal.

6. The sheet must be compacted when bending to prevent the sheet from lifting and hurting people during bending.

7. When changing the opening of the variable lower die of the bending machine, no material is allowed to come into contact with the lower die.

After reading the article, I believe that everyone has a more detailed understanding of the operation of the bending machine. If you have any doubts, you can contact us at any time!

Relevant Information

Secretary of the Municipal Youth League Committee - Qian Jun came to our company for research and inspection
See more information 白箭头 黑箭头
The secretary of the provincial party committee came to our company to guide the work
See more information 白箭头 黑箭头
District People's Congress representative Chairman Xie came to our company for research
See more information 白箭头 黑箭头

Address:West of Jiubo Science and Technology Park, Bowang Town, Bowang District, Ma'anshan, Anhui

Tel:0555-6762898

这是描述信息
这是描述信息
这是描述信息

About Us

>

Proudct Center

>

News

>

Marketing & Service

>

YAWEI

Scan QR code

Follow us

Anhui Yawei Machine Tool Manufacturing Co., Ltd. All rights reserved.    皖ICP备18020142-1号    Technical support: www.300.cn Nanjing